Liner Coating | Sermed Havuz Sistemleri
×

HAVUZ TALEBİNİZ SADECE 3 ADIMDA HAYALDEN GERÇEĞE DÖNÜŞSÜN!

1 BAHÇENİN RESMİNİ ÇEK!
2 WHATSAPP'DAN
0532 111 73 73'E GÖNDER
3HAVUZUNUZ BAHÇENİZE GELSİN!

Görüş ve önerileriniz için lütfen info@sermedhavuz.com.tr mail adresine talebinizi iletin. Teşekkür ederiz!

YOU POOL REQUEST WILL BE TURNED FROM DREAM INTO REAL ONLY IN THREE STEPS!

1 TAKE A PICTURE OF GARDEN!
2 SEND TO +90 532 111 73 73 VIA WHATSAPP
3YOUR POOL COMES TO YOUR GARDEN!

Please e-mail your request to info@sermedhavuz.com.tr for your comments and suggestions.

DO NOT STRUGGLE WITH PROBLEM OF THE POOL,
JUST ENJOY IT

The liner is applied directly to the reinforced concrete surface of pool and is elastic. For this reason, the structure is less affected from movements and damages that may occur in bearing system due to sitting movements or earthquake effect, compared to alternative pool inner coatings. The liner may continue to sealing feature even in the event of cracks in pool carrier system. In addition, compensation for damage to the material caused by any reason, even complete replacement of coating, is a process that is independent from carrier system and it can be realized in a short time

It has anti-algae feature, it does not hold algae thanks to its special outer surface.

It is antibacterial. It does not contain bacteria. (Operating rooms are now using liner too)

Annual maintenance and cleaning is easy; and cheap.

It does not leak water; it is resistant to earthquake and soil settlement.

Thanks to its flexible structure, it is not affected by ground movements.

100% waterproofing is guaranteed. If it is not cut off consciously, it will not leak water.

It is anti-toxic, does not contain carcinogenic substances.

Less chlorine is used because it does not contain bacteria on its surface. (40% less)

There is no need to use reinforced concrete, insulation materials and water joint tapes.

It is not necessary to empty pool water.

The system is suitable for this.

It is difficult to experience deformations over time.

It does not stick to reinforced concrete surface in any way.

Therefore, it is not affected by problems in construction.

It is not affected by earthquake thanks to its flexible structure.

It does not crackage or puncture in icing.

It is applied in rolls. Its montage is done in way to placement of rollers on each other with a special welding machine.

It is resistant UV sun ray.

The surface in joints is suitable for algae formation.

Joint spaces are suitable for microbial growth.

It should be avoided to use in environments such as hospitals, operating rooms, pools.

Cleaning between ceramic joints is troublesome and costly.

Small cracks forming because of settling of the ground, earthquake etc., cause water leaks.

It leaks water because plastic blowing nozzles applied to concrete work differently from concrete.

More chlorine is used to struggle with bacteria. (Carcinogenic effect of chlorine is detected.)

It is required to use make reinforced concrete, interior-exterior plaster, cement finish and their insulation and using water-retaining tapes.

Water for ceramics cleaning needs to be emptied every year.

This application causes ceramics to be poured over time due to different pressure on reinforced concrete surface.

Due to the adhesion on concrete screen and floor with the ceramic adhesive, events such as settling of floor and earthquake cause cracks.

Cracks and spills, small cracks can occur. It is mounted on concrete screen and floor with ceramic adhesive.

Feeding nozzles, lighting and skimmers are mounted on screen, so it works differently on grounds in case of as earthquake, and there are problems in piping.

Swimming Pool
Liner Coating,
Mounting Technique

LINER COATING MONTAGE TECHNIQUE

The PVC membrane is prepared by opening on a smooth and clean surface, the parts to be
welded are prepared by cutting and firstly angle bracket montage is done.

In flooded pools, overlaying process starts with overflow drain. Since both sides of overflow
drain are covered with PVC-coated brackets, furnishing of liner into drain is extremely easy in flat pools. In amorphous pools, it is necessary to nailing flat lath or clinching
liner on internal corners of overflow drain. After this process, side walls of pool are coated. In order to achieve this coating, the pre-prepared PVC membrane is hanged
by stretching in a way not make pots to existing brackets on upper corner. All side surfaces are coated in this manner. After making sure that laid materials do not make
pots, welding operations are started. Side surfaces and joining to floor are as follows.

After PVC membrane coating process is finished, pool is filled with water, a depth for about 20 cm. Thus, PVC membrane is stretched and flanges are
mounted and opened. In addition, nozzles in wall and flanges of underwater lamps are installed by filling water up to 10 cm below relevant site.

On ladder steps and other slippery surfaces, nonslip Membranes are
placed on existing flat PVC membranes if desired. Membranes are placed with
adhesive or hot air welding system.

Please enter your email address for Liner Coating price offer and subscription.

FOLLOW WE!

© 2017 All rights reserved. Sermed Havuz Sistemleri Eğitim Sağlık İnşaat San. Tic. Ltd. Şti.

REQUEST OFFER FORM

TOP